Skip to content
  • Free Delivery

  • Buy Direct from the Makers

  • Aftersales Support

Robot Lawn Mower Common Faults and Solutions

Share
Link
https://eu.cleva.com/en-fr/blogs/lawnmaster-robotic-lawn-mowers-tips-guides/robot-lawn-mower-common-faults-and-solutions

Smart robotic lawn mowers bring effortless, automated maintenance to modern lawns. However, complex terrain, thick grass, debris, or dirty sensors can occasionally cause stops or uneven cuts.

Designed specifically for LawnMaster robotic lawn mowers, this guide provides a systematic breakdown of common operational issues and official solutions for vision-based and boundaryless models.

Lawnmaster-Robotic_Lawnmower-FAQs

1. Movement & Operation Issues

Mower Gets Stuck Frequently

Symptoms: The mower stops mid-lawn or near obstacles with a "Stuck" alert on the control panel or app.

Common Causes:

  1. Grass clippings, twigs, or debris wrapped around the drive wheels or blade disc.
  2. Dips, ruts, or puddles causing wheels to lose traction.
  3. Lift or obstruction sensors triggered repeatedly.

Solutions:

  1. Clear Debris: Press STOP, remove the isolator key and battery pack, put on protective gloves, and clear wrapped material from the wheel axles and blade disc.
  2. Level the Lawn: Fill holes with topsoil and reseed to prevent wheel entrapment and water pooling.
  3. Avoid Standing Water: Relocate the mower away from puddles (never submerge or pressure-wash the mower).

Mower Runs Outside Working Area

Symptoms: The mower crosses grass edges into flowerbeds, paved pathways, or gravel areas.

Common Causes:

  1. Lack of a clear physical or visual border (e.g., missing a 35 cm wide level margin or a raised barrier higher than 15 cm).
  2. Ultrasonic obstacle sensors are turned off in settings.

Solutions:

  1. Define Borders: Maintain clear, neat lawn margins, or place temporary physical barriers (e.g., garden stakes) around flowerbeds and drop-offs.
  2. Enable Obstacle Avoidance: Turn on ultrasonic sensors via the control panel or app.

Mower Tilted or Upside Down

Symptoms: Mower tips sideways on uneven terrain and shuts down safety sensors.

Solution: Place the mower upright, check the ground for exposed tree roots, loose rocks, or steep dips, eliminate terrain hazards, and restart the unit.

Lawnmaster-VBRM18AMDR-Carry-handle-Solutions

2. Startup & LED Indicator Troubleshooting

Fault / Symptom Potential Causes Troubleshooting & Solution
Mower fails to turn on or start
  • Isolator key loose or missing
  • Battery not fully clicked in or depleted
  • Initial grass height exceeds 60 mm
  1. Insert and secure the isolator key; push battery in until it clicks.
  2. Fully charge the battery.
System Status & Error Diagnostics
  • Lift or bump sensors continuously triggered
  • Mower is tilted
  • Lawn unrecognized (grass too tall or non-grass surface)
  1. Clear obstacles and level uneven ground.
  2. Relocate mower onto a standard lawn area.
  3. Remove and re-insert the isolator key to restart.
Error Indicator: Solid Red Light
  • Motor overload or stalled blade disc
  • Sensor communication fault
  • System operational error
  1. Power off, inspect drive wheels and blade disc for jams.
  2. Raise cutting height setting to reduce motor strain.
  3. Re-insert isolator key to reset and restart.
Indicator: Flashing Red or Yellow Light
  • Camera communication error (insufficient light)
  • Battery temperature out of range (too hot/cold)
  1. Vision camera mowers require daylight; avoid night operation.
  2. Allow battery to reach safe operating temperature (4℃ to 40℃) before restarting.

3. Cutting Quality & Blade Maintenance

Mower Moves Upon Startup, But Blade Disc Does Not Rotate

Cause: Vision-guided mowers run a 5-second path recognition routine after power-on before engaging the cutting disc. This is a standard safety protocol.

Solution: Blades engage automatically after 5 seconds of continuous motion. If the disc remains stationary while driving normally, power off and inspect for mechanical jams.

Uneven Grass Cut or Shredded Blade Tips

Common Causes:

  1. Dull or grass-clogged blades.
  2. Mowing wet or overly dense grass, causing tearing rather than clean cutting.

Solutions:

  1. Avoid mowing wet lawns; allow the grass to dry before operating.
  2. Replace dull blades promptly. Replace all blades simultaneously as a complete set.

Excessive Vibration During Operation

Cause: Unbalanced blade disc. Usually caused by stacking multiple blades under a single screw, mixing different blade types/thicknesses, or loose mounting hardware.

Solutions:

  1. Inspect the blade disc to ensure exactly one blade is mounted per screw position, pivoting freely.
  2. Replace all 3 blades and screws together as a matched set, making sure screws are securely tightened.

Reduced Runtime Per Charge

Cause: Cutting height set too low on thick grass, forcing the motor to draw extra power; incomplete charge cycle.

Solution: Raise the cutting height setting and mow more frequently; ensure the battery reaches full charge in suitable ambient temperatures.

Lawnmaster-AMB16P-rain-sensor

4. Daily Preventative Maintenance

  • Follow Safety Protocols: Always press STOP, remove the safety isolator key, and disconnect the battery pack before inspecting the undercarriage or changing blades.
  • Avoid High-Pressure Water: Although rated for outdoor splash protection, never use high-pressure hoses or submerge the mower. Use a brush and damp cloth for cleaning.
  • Winter Storage Routine: Clean the machine thoroughly before winter storage. Remove the battery and isolator key, storing them indoors between 0℃ and 25℃. Recharge lithium batteries to 30%–50% every 6 months during extended storage to maintain cell health.